PU-gecoate Nylon Spuitoverall - Cat III Type 6

5136xx

Spuitoverall met de hoogste bescherming tegen het binnendringen van verfspatten, gecombineerd met een hoog draagcomfort. De spuitoverall is voorzien van een PU-coating en is getest en gecertificeerd volgens de EU PBM-verordening 2016/425 als categorie III. Hij biedt optimale bescherming tegen spuitnevel en voorkomt verontreiniging van de lak door vezels, stof of pluisjes.

Wit met carbonstriping
Semi-transparant
Representatieve uitstraling
Antistatisch (EN 1149-5:2018) & stof- en pluisvrij
Beschermt tegen overspray en binnendringen van verfspatten (EN 13034:2005+A1:2009)
Perfecte pasvorm voor alle maten en comfortabel om de hele dag te dragen
Goede pasvorm rond nek, polsen en enkels, verstelbare capuchon
Stevige, hoogwaardige 2-weg rits

Tijdens het voorbereidings- en spuitwerk dienen de gebruikers zich te beschermen tegen bepaalde risico’s waaraan ze worden blootgesteld. Onze beschermende kleding biedt niet alleen bescherming, maar ook comfort en duurzaamheid. Afhankelijk van het soort werk bieden we ofwel herbruikbare of wegwerp stof- & spuitmaskers, handschoenen en spuitoveralls.

Bekijk hier ons volledige assortiment voor Persoonlijke Beschermingsmiddelen.

Eleven steps, five phases. Work top to bottom each phase sets up the next.

Phase 1 · Prepare (Step 1) Gear up and confirm your PPE fits before touching the panel.

Phase 2 · Assess (Steps 2–3) Read the damage, then clear anything in the repair's way.

Phase 3 · Isolate (Steps 4–5) Decontaminate the surface and mask off everything you're not repairing.

Phase 4 · Repair (Steps 6–8) Sand out the scratch, refine the pattern, and clean back to a checkable surface.

Phase 5 · Finish (Steps 9–11) Use heat tools safely, prepare for refinishing, and sign off on the final inspection.

Required Personal Protection Equipment (PPE)

Before starting the repair, wear the recommended personal protection equipment:

1. Bodyguard Coverall - Article No. 5200XX

PPE Category I
Protects clothing against dust and workshop contamination
Comfortable for extended use

2. Cut Resistant Gloves - Article No. 53200X

Certified according to EN 388
Protects hands against sharp edges during trim removal and repair work

3. Safety Goggles - Article No. 5088

Certified according to EN ISO 16321-1
Protects eyes against flying particles, dust and debris

4. Active Carbon Mask - Article No. 5525

Certified according to EN 149
Helps protect against dust and possible fumes generated during repair activities

Step 1

Prepare Yourself Safely

Put on:

BodyGuard Coverall (5200XX)
Cut Resistant Gloves (53200X)
Safety Goggles (5088)
Active Carbon Mask (5525)

Ensure all PPE fits properly before beginning the repair.

Step 2

Inspect the Damage

Examine the scratched panel carefully.

Identify:

Scratch depth
Size of the damaged area
Potential damage to surrounding components

Use suitable lighting to determine the correct repair method.

Step 3

Remove Obstructions

Carefully remove mouldings, trims, badges or other components that may interfere with the repair.

Safety Tip
Wear the EN 388 certified gloves (53200X) to protect your hands from sharp edges and trim clips.

Step 4

Clean and Degrease the Surface

Thoroughly clean the repair area to remove:

Dirt
Grease
Silicone contamination
Wax residues

A clean surface prevents contamination from being sanded into the paint system.

Step 5

Protect Adjacent Areas

Mask surrounding panels and sensitive parts to avoid accidental damage during sanding and repair work.

Step 6

Remove the Scratch

Sand the damaged area using the appropriate abrasive grade.

Work carefully within the repair area and avoid unnecessary removal of surrounding paint.

Best Practice

Use controlled pressure and inspect progress regularly.

Step 7

Refine the Sanding Pattern

Refine the initial sanding marks using finer abrasives until a uniform sanding pattern is achieved.

This step prepares the surface for polishing and finishing.

Step 8

Clean and Inspect

Remove all sanding dust and inspect the panel.

Look for:

Remaining scratch marks
Deep sanding scratches
Uneven repair areas

Repeat refinement if necessary.

Step 9

Use Heat Tools Safely

When using a heat gun or adhesive eraser:

Wear Safety Goggles (5088)
Wear the Active Carbon Mask (5525)
Maintain adequate ventilation

This helps protect against airborne particles and possible fumes.

Step 10

Prepare for Finishing

Once the scratch has been removed and the sanding pattern refined, prepare the panel for compounding, polishing or the next refinishing step.

Step 11

Final Inspection

Inspect the repaired area under suitable lighting.

Confirm:

Scratch removal is complete
Surface preparation is uniform
No contamination is present
The panel is ready for finishing

Best Practices

✓ Always wear the recommended PPE.

✓ Remove trims and obstructions before sanding.

✓ Clean before sanding.

✓ Use the correct abrasive sequence.

✓ Inspect frequently during the repair.