FOL 62 - Logo tape adhesive transfer 50mm x 300mm 10p.
FOL 62
Revive your logos and emblems with our Logo Tape. This adhesive transfer, measuring 50mm x 300mm, offers a simple re-fixing solution. After cleaning the surface and logo with degreaser, remove the cover strip, press the logo onto the adhesive transfer for a few seconds, and then remove the transfer. Your logo is now securely attached to the bodywork with adhesive in all the right places.
Key features
-
- • Adhesive transfer with dimensions 50mm x 300mm for re-fixing logos / emblems on to the panel.
-
- • Clean surface and logo with degreaser, remove cover strip, press the logo down on the adhesive transfer for several seconds and remove adhesive transfer.
-
- • The logo now has enough adhesive in all the right places to be attached permanently to the body work.
Product details
- Brand
- Finixa
- Number
- FOL 62
- Colour
- Transparent
- Width (cm)
- 5
- Shelf life
- 24 months
- Dry storage
- yes
- Minimum storing temperature
- -40 °C
- Storing condition
- dark
- Freezing resistant
- yes
- Units for outer box
- 50
- Application areas
- exterior
- Application surfaces
- steel; E-coating; galvanized steel; aluminum; fiberglass; hard plastic; soft plastic; chrome; new paint; good paint; neglected paint; matt paint; putty; primer/filler; OEM paint; refinish paint; wood; zinc; enamel; ceramic; copper; lead; stainless steel; high-pressure laminate; polyethylene; polypropylene; polycarbonate; polymethyl methacrylate; polytetrafluoroethylene; chlorides; thermosetting composites; carbon fiber; thermoplastics; coated metals
- Corrosive to metals
- no
- Free of isocyanates
- yes
- Maximum processing temperature
- 35 °C
- Minimum processing temperature
- -10 °C
- Tensile Strength (Ncm)
- 87.5 N/cm²
- Thickness
- 0.04 cm
- Workable surface state
- dry
Application
-
FOL 62 application - Directions for Use:
- Surface Preparation: Ensure all surfaces are clean, dry, and free of grease or dust.
- Measure and Mark: Position where you want to apply the logo and mark lightly if necessary.
- Peel: Peel off the backing and carefully place the logo on the adhesive side.
- Apply Pressure: Press firmly for at least 30 seconds to secure adhesion.
- Peel and stick: peel of the logo from the adhesive and stick it on the marked area of the surface, firmly press while apllying to ensure good adhesion.
- Curing Time: Allow a minimum of 24 hours for full adhesive bonding.
Downloads
Language
| Name | Asset Type | Language | File type | Download |
|---|---|---|---|---|
| FOL 62 - TDS - Finixa - EN.pdf | TDS | English | 104 KB | |
| 05 Product comparison.pdf | Product_comparison | English | 52 KB | |
| FOL 62 - TDS - Finixa - NL.pdf | TDS | Nederlands | 107 KB | |
| 05 Productvergelijking.pdf | Product_comparison | Nederlands | 52 KB | |
| FOL 62 - TDS - Finixa - DE.pdf | TDS | Deutsch | 110 KB | |
| 05 Produktvergleich.pdf | Product_comparison | Deutsch | 54 KB | |
| FOL 62 - TDS - Finixa - EN.pdf | TDS | Español | 104 KB | |
| 05 Comparación de productos.pdf | Product_comparison | Español | 54 KB | |
| FOL 62 - TDS - Finixa - FR.pdf | TDS | Français | 108 KB | |
| 05 Comparaison des produits.pdf | Product_comparison | Français | 54 KB |